Buy Millipore CHGE71TF3, SHF Cartridge Filter, 10", Fluoroelastomer

info@PrimeLabMed.com

1-855-590-6919
1-908-282-3482 (Intl.)

Pictures shown are for illustrative purpose only. Actual product may vary

Options and Related Products

Millipore, CHGE71TF3, SHF Cartridge Filter, Pore Size 0.5/0.2 Um, Cartridge Nominal Length 10", Code 7, Fluoroelastomer Seal

Features:

Organism Retention: Microorganism
Mode of Action: Filtration (size exclusion)
Application: BioProcessing
Intended Use: Reduction or removal of microorganism/bioburden
Instructions for Use: Please refer wetting instructions of Filters with MILLIPORE EXPRESS Membrane user guide
Storage Statement: Please refer Filters with MILLIPORE EXPRESS Membrane user guide
Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Preparation Note

Sterilization Method
25 forward or 22 forward and 3 reverse SIP cycles of 30 min at 135 °C and 0.35 bar (5) or 3 forward SIP cycles of 30 min at 135 °C and 1 bar (15 psid); 25 autoclave cycles of 60 min at 126 °C

Analysis Note

Bacterial Retention
TOC/Conductivity
After sterilization and a controlled water flush of 20 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.
Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥2 L

We aim to show you accurate product information. Here you will find what the manufacturers have provided us with. See our disclaimer.

Technical Details

Device Configuration	Cartridge
Maximum Inlet Pressure, bar (psi)	Forward - 7 bar (100 psi) at 25 °C; 1.7 bar (25 psi) at 80 °C; 1.0 bar (15 psi) at 135 °C; Reverse - 2.07 bar (30 psi) at 25 °C; 0.07 bar (1 psi) at 135 °C
Cartridge Code	Code 7
Quality Level	MQ400
Bacterial Endotoxins	Aqueous extraction contains ≤0.25 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test
Sterilization	25 forward or 22 forward and 3 reverse SIP cycles of 30 min at 135 °C and 0.35 bar (5) or 3 forward SIP cycles of 30 min at 135 °C and 1 bar (15 psid); 25 autoclave cycles of 60 min at 126 °C
Wettability	Hydrophilic
Pore Size	0.5 / 0.2 µm
Air Diffusion at 23 °C	≤28.2 mL/min at 2.8 bar (40 psig) in water
Bubble Point at 23 °C	≥4000 mbar (58 psig) air with water
Indirect Food Additive	All component materials meet the FDA Indirect Food Additive requirements cited in 21 CFR 177-182.
Maximum Differential Pressure	Forward: 6900 mbar (100 psi) at 25 °C; 1700 bar (25 psi) at 80 °C; 340 mbar (5 psi) at 135 °C. Reverse: 2100 mbar (30 psi) at 25 °C, 69 mbar (1 psi) at 135 °C
Cartridge Nominal Length	10 in. (25 cm)
Diameter	6.9 cm (2.7 in.)
Filtration Area	0.49 m2
Device Size	10 in.
Chemistry	Polyethersulfone (PES)
Device Material	Polypropylene/Polysulfone
Seal Material	Fluorocarbon rubber
Support Material	Polypropylene

Device Configuration	Cartridge
Maximum Inlet Pressure, bar (psi)	Forward - 7 bar (100 psi) at 25 °C; 1.7 bar (25 psi) at 80 °C; 1.0 bar (15 psi) at 135 °C; Reverse - 2.07 bar (30 psi) at 25 °C; 0.07 bar (1 psi) at 135 °C
Cartridge Code	Code 7
Quality Level	MQ400
Bacterial Endotoxins	Aqueous extraction contains ≤0.25 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test
Sterilization	25 forward or 22 forward and 3 reverse SIP cycles of 30 min at 135 °C and 0.35 bar (5) or 3 forward SIP cycles of 30 min at 135 °C and 1 bar (15 psid); 25 autoclave cycles of 60 min at 126 °C
Wettability	Hydrophilic
Pore Size	0.5 / 0.2 µm
Air Diffusion at 23 °C	≤28.2 mL/min at 2.8 bar (40 psig) in water
Bubble Point at 23 °C	≥4000 mbar (58 psig) air with water
Indirect Food Additive	All component materials meet the FDA Indirect Food Additive requirements cited in 21 CFR 177-182.
Maximum Differential Pressure	Forward: 6900 mbar (100 psi) at 25 °C; 1700 bar (25 psi) at 80 °C; 340 mbar (5 psi) at 135 °C. Reverse: 2100 mbar (30 psi) at 25 °C, 69 mbar (1 psi) at 135 °C
Cartridge Nominal Length	10 in. (25 cm)
Diameter	6.9 cm (2.7 in.)
Filtration Area	0.49 m2
Device Size	10 in.
Chemistry	Polyethersulfone (PES)
Device Material	Polypropylene/Polysulfone
Seal Material	Fluorocarbon rubber
Support Material	Polypropylene

Note: Please read description carefully. Do not base your order on the picture presented.