Buy Millipore KPGES05TH1, Opticap Filter XL 5 PHF, Sterile, Inlet 1.5", 5"

info@PrimeLabMed.com

1-855-590-6919
1-908-282-3482 (Intl.)

Pictures shown are for illustrative purpose only. Actual product may vary

Options and Related Products

Millipore, KPGES05TH1, Opticap Filter XL 5 Express PHF Sterile 0.2 Um 1-1/2" TC-9/16" HB

Features:

Organism Retention: Microorganism
Mode of Action: Filtration (size exclusion)
Application: BioProcessing
Intended Use: Reduction or removal of microorganism/bioburden
Instructions for Use: Please refer wetting instructions of Filters with MILLIPORE EXPRESS® Membrane user guide
Storage Statement: Please refer Filters with MILLIPORE EXPRESS® Membrane user guide
Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Preparation Note

Sterilization Method
3 autoclave cycles of 60 min at 123 °C; not in-line steam sterilizable
This product was manufactured with a Millipore Express® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Analysis Note

Bacterial Retention
Samples of membrane used in this filter were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration
TOC/Conductivity
After sterilization and a controlled water flush of 6.0 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.
Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥1 L

We aim to show you accurate product information. Here you will find what the manufacturers have provided us with. See our disclaimer.

Technical Details

Device Configuration	Capsule
Connections, Inlet/Outlet	38 mm (1-1/2 in.) Sanitary Flange/14 mm (9/16 in.) Hose Barb
Connections, Vent/Drain	1/4 in. Hose Barb with double O-ring seal
Housing Material	Polypropylene (PP)
Maximum Inlet Pressure, bar (psi)	5.5 bar (80 psi) at 25 °C; 2.75 bar (40 psi) at 60 °C; 1.0 bar (15 psi) at 80 °C
Bacterial Endotoxins	Aqueous extraction contains ≤0.25 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test
Sterility	Sterile
Sterilization	3 autoclave cycles of 60 min at 123 °C; not in-line steam sterilizable
Wettability	Hydrophilic
Pore Size	0.2 µm
Inlet Connection	Sanitary Flange
Outlet Connection	Hose Barb
Air Diffusion at 23 °C	≤17.4 mL/min at 2.8 bar (40 psig) in water
Indirect Food Additive	All component materials meet the FDA Indirect Food Additive requirements cited in 21 CFR 177-182.
Maximum Inlet Pressure (psig)	80 psig
Maximum Differential Pressure	5500 mbar (80 psi) at 25 °C; 1000 bar (15 psi) at 80 °C
Maximum Inlet Temperature	25 °C
Cartridge Nominal Length	5 in. (12.5 cm)
Length	21.6 cm (8.5 in.)
Diameter	10.7 cm (4.2 in.)
Filtration Area	0.31 m2
Inlet to Outlet Width	21.6 cm (8.5 in.)
Device Size	5 in.
Inlet Connection Diameter	1-1/2 in.
Outlet Connection Diameter	9/16 in.
Chemistry	Polyethersulfone (PES)
Device Material	Gamma stable polypropylene/Polysulfone
Seal Material	Silicone (SI)
Support Material	Polyester
Vent Cap Material	Polypropylene (PP)

Device Configuration	Capsule
Connections, Inlet/Outlet	38 mm (1-1/2 in.) Sanitary Flange/14 mm (9/16 in.) Hose Barb
Connections, Vent/Drain	1/4 in. Hose Barb with double O-ring seal
Housing Material	Polypropylene (PP)
Maximum Inlet Pressure, bar (psi)	5.5 bar (80 psi) at 25 °C; 2.75 bar (40 psi) at 60 °C; 1.0 bar (15 psi) at 80 °C
Bacterial Endotoxins	Aqueous extraction contains ≤0.25 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test
Sterility	Sterile
Sterilization	3 autoclave cycles of 60 min at 123 °C; not in-line steam sterilizable
Wettability	Hydrophilic
Pore Size	0.2 µm
Inlet Connection	Sanitary Flange
Outlet Connection	Hose Barb
Air Diffusion at 23 °C	≤17.4 mL/min at 2.8 bar (40 psig) in water
Indirect Food Additive	All component materials meet the FDA Indirect Food Additive requirements cited in 21 CFR 177-182.
Maximum Inlet Pressure (psig)	80 psig
Maximum Differential Pressure	5500 mbar (80 psi) at 25 °C; 1000 bar (15 psi) at 80 °C
Maximum Inlet Temperature	25 °C
Cartridge Nominal Length	5 in. (12.5 cm)
Length	21.6 cm (8.5 in.)
Diameter	10.7 cm (4.2 in.)
Filtration Area	0.31 m2
Inlet to Outlet Width	21.6 cm (8.5 in.)
Device Size	5 in.
Inlet Connection Diameter	1-1/2 in.
Outlet Connection Diameter	9/16 in.
Chemistry	Polyethersulfone (PES)
Device Material	Gamma stable polypropylene/Polysulfone
Seal Material	Silicone (SI)
Support Material	Polyester
Vent Cap Material	Polypropylene (PP)

Note: Please read description carefully. Do not base your order on the picture presented.